P2P connection throughput up to 450+Mbps

BS9 adopts of 11AC wave2 technology, it delivers 867Mbps speed rate at 5GHz radio. Come with Gigabit ethernet LAN port design , the maximum throughput test for PtP connection can be up to 450Mbps.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become “hidden nodes” and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.

iLink–Auto-bridge technology enable it to easy setup

iLink is IP-COM proprietary auto-bridge technology, It enables the basestation or CPE in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especilly for for CCTV surveillance transmission application.

Easy to Setup and Manage

BS9 comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, BS9 can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

25km+ transmission Range

iLBE-5AC adopts of independent external power amplifier and 23dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 25km.

P2P Connection Throughput up to 450+Mbps

iLBE-5AC adopt of 11AC wave2 technology, it delivers 867Mbps speed rate at 5GHz radio. Come with Gigabit ethernet LAN port design , the maximum throughput test for PtP connection can be up to 450Mbps.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become “hidden nodes” and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.”

iLink–Auto-bridge Technology Enable it To Easy Setup

iLink is IP-COM proprietary auto-bridge technology, It enables the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especilly for for CCTV surveillance transmission application.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, iLBE-5AC can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

Multiple Application Scenarios

Long-Distance Wireless Connection
One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.
WISP(Client+Router) Mode
Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

Easy to Setup and Manage

iLBE-5AC comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

20+km transmission Range

Wavebeam M5 adopts of independent external power amplifier and 23dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 20km.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become “hidden nodes” and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.

iLink–Auto-bridge Technology Enable it To Easy Setup

iLink is IP-COM proprietary auto-bridge technology. It enables the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especilly for for CCTV surveillance transmission application.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, Wavebeam M5 can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

Easy to Setup and Manage

Wavebeam M5 comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Multiple Application Scenarios

Long-Distance Wireless Connection
One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.
WISP(Client+Router) Mode
Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

10+km transmission Range

MS-5AC adopts of independent external power amplifier and 16dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 10km.

P2P connection throughput up to 450+Mbps

MS-5AC adopt of 11AC wave2 technology, it delivers 867Mbps speed rate at 5GHz radio. Come with Gigabit ethernet LAN port design , the maximum throughput test for PtP connection can be up to 450Mbps.

Flexible power supply method enable it easy to deployment

MS-5AC support PoE 802.3af/at, 24V 0.5A Passive PoE and 12V 1A DC power supply optional. It helps the engineer to deployment the device flexiblely.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become“hidden nodes” and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.

iLink–Auto-bridge technology enable it to easy setup

iLink is IP-COM proprietary auto-bridge technology, It enables the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especilly for for CCTV surveillance transmission application.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, MS-5AC can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

Easy to Setup and Manage

MS-5AC comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Multiple Application Scenarios

Long-Distance Wireless Connection
One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.
WISP(Client+Router) Mode
Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

5+km transmission range

CPE12(MS-Loco5AC) adopts of internal power amplifier and 12dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 5km.

Flexible power supply method enable it easy to deployment

CPE12(MS-Loco5AC) support PoE 802.3af/at, 12V 1A Passive PoE and 12V 1A DC power supply optional. It helps the engineer to deployment the device flexiblely.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor enviroment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become“hidden nodes”and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.

iLink–Auto-bridge technology enable it to easy setup

For single pack, auto-bridge technology makes the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. For the kit pack, the two CPESs inside are pre-configured at the factory, so plug and play is supported without manual pairing. It is very useful for the person who is not familiar with network knowledge, especially for CCTV surveillance transmission application.

Easy to setup and manage

CPE12(MS-Loco5AC) comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Professional outdoor design

Equipped with IP65 waterproof enclouse and high quality hardware design, MS-Loco5AC can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment.

5km+ transmission Range

CPE9 adopts of independent power amplifier and 12dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 5km.

Auto-bridge For Two Device

CPE9 adopts of auto-bridge technology,two cpe can connect to each other when you power on them face to face. It is very easy to setup.

Multiple Application Scenarios

Long-Distance Wireless Connection
One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.
WISP(Client+Router) Mode
Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

Smart Signal Indicator LED

3 signal LED Lights represent the currently signal strength that CPE9 receives from peer device.It is helpful to find the right location to deploy the device and achieve a better performance.

Professional Outdoor Design

Equipped with IP64 waterproof enclouse and high quality hardware design, CPE9 can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment.

Easy to Setup and Manage

CPE9 comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

5+km transmission Range

CPE6S adopts of internal power amplifier and 12dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 5km.

Flexible power supply method enable it easy to deployment

CPE6S support 12V 1A Passive PoE and 12V 1A DC power supply optional. It helps the engineer to deployment the device flexiblely.

ipMAX–IP-COM TDMA proprietary protocol

ipMAX is IP-COM TDMA (Time Division Multiple Access) proprietary protocol to improve performance and capacity for wireless P2MP outdoor application scenarios. In outdoor environment, the CPE use highly directional antennas to connect to the Basestation from distances that can span several kilometers. the CPE can’t sense each other, they become “hidden nodes” and cannot coordinate access to the wireless channel. Thus the Basestation experiences frequent collisions from stations transmitting simultaneously. As the network scales, these collisions build up exponentially, increasing latency and lowering throughput. With ipMAX, it coordinate all the data transmission and allocates time to active clients to provide greater noise immunity performance when compared to the conventional 802.11 CSMA/CA (Carrier Sense Multiple Access / Collision Avoidance) protocol.

Auto-bridge technology enable it to easy setup

For single pack，iLink, IP-COM proprietary auto-bridge technology, makes the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. For the kit pack, the two CPESs inside are pre-configured at the factory, so plug and play is supported without manual pairing. It is very useful for the person who is not familiar with network knowledge, especially for CCTV surveillance transmission application.

Easy to Setup and Manage

CPE6S comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, CPE6S can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

1+km transmission Range

CPE5 adopts of internal power amplifier and 9dBi directional antenna to provide an efficient way to pick up and maintain a stable signal for a wireless network up to 1km.

Flexible power supply method enable it easy to deployment

CPE5 supports 12V 1A Passive PoE and 12V 1A DC power supply option. It helps the engineer to deploy the device flexiblely.

iLink–Auto-bridge technology enable it to easy setup

iLink is IP-COM proprietary auto-bridge technology, It enables the CPE or basestation in factory default settings connect to each other automaticaly after the device is powered on. It is very useful for the person who is not familiar with network knowledge, especially for CCTV surveillance transmission application.

Easy to Setup and Manage

CPE5 comes with a centralized management software that helps users easily to manage all the devices in the network from a single PC-CPE Controller.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, CPE5 can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment.

Auto-bridge For Two Device

CPE3 adopts of auto-bridge technology,two cpe can connect to each other when you power on them face to face. It is very easy to setup.

8dBi Directional Antenna

CPE3 integrates with a 8dBi directional antenna to provide an optimized transmission quality.

Professional Outdoor Design

Equipped with IP65 waterproof enclouse and high quality hardware design, CPE3 can work in various weather conditions, such as sunshine, rainfall or extremely low/high temperature environment

Long-Distance Wireless Connection

One work as AP mode and another work as Station mode to create a long distance wrieless connecton for video surveillance and data transmission.

WISP(Client+Router) Mode

Wirelessly connect to WISP station/hotspot to share Internet to local wireless and wired network.

Smart Signal Indicator LED

3 signal LED Lights represent the currently signal strength that CPE3 receives from peer device.It is helpful to find the right location to deploy the device and achieve a better performance.

IP65 protection

Professional materials and design guarantee iUAP-AC-M an IP65 enclosure for harsh environments both indoors and outdoors.

IEEE 802.11ac Wave2 and MU-MIMO

Powered by MU-MIMO technology, a single iUAP-AC-M can communicate with multiple wireless clients at the same time, letting you enjoy higher throughput and better experience.

Dual-band for more connected clients

iUAP-AC-M allows clients that support either 2.4 GHz or 5 GHz band, or both to connect to it at the same time, tripling the quantity of connected clients of traditional single-band AP.

High-gain omni-directional antennas

Equipped with two 5 dBi high-gain omni-directional antennas, iUAP-AC-M provides a maximum coverage radius of 200 meters. iUAP-AC-M can meet different requirements by connecting antennas of different specifications to the standard RP-SMA connectors.

Built-in RF for intelligent optimization

Featuring various anti-interference algorithms, the built-in RF enables iUAP-AC-M to evenly allocate bandwidth resources for multiple users, filter interference, and optimize data rate, offering you a guaranteed signal strength and reliable wireless experience.

VLAN tagging for SSID

iUAP-AC-M allows you to set multiple SSIDs and add VLAN tags for SSIDs, thus protecting your network.

Standard PoE sourcing and DC power supply for easy deployment

You can use an IEEE 802.3af-compliant PoE sourcing equipment, or a 24V DC power adapter to power on iUAP-AC-M.

Centralized management

The ProFi Controller makes it easy to manage and monitor the whole ProFi devices in a real-time manner and the cloud services enable a remote and secure access free from the restrictions of device location.